Polaris 2014 Sportsman 570 EF Service Manual Download Page 340

Page: 340 / 456

8.22

9924871 R03 - 2014 Polaris Sportsman® 570 EFI Service Manual

11. Install all new seals into the gearcases. Use the Rear

Output

Seal

Driver

(PN

2871698)

and

Rear

Driveshaft Seal Guide (PN 2871699) to install the
seals into the gearcase halves (refer to the following
illustration

identify

the

seals

needing

replacement).

12. Thoroughly clean the shift shaft housing.

Be sure

the

transmission

Reverse

prior

reassembly.

13. Install the sector gear (16T) onto the shift drum shaft.

Install the shift shaft assembly and sector gear (11T)
into the bushing pocket on the left side. Align the
timing marks on the gears as shown.

TRANSMISSION

Summary of Contents for 2014 Sportsman 570 EF


























































































































































































































































































































































































































Search results

Summary of Contents for 2014 Sportsman 570 EF

Reviews:

Related manuals for 2014 Sportsman 570 EF

Brands by name

Popular brands

Polaris 2014 Sportsman 570 EF, Service Manual

Search results

Summary of Contents for 2014 Sportsman 570 EF

Reviews:

Related manuals for 2014 Sportsman 570 EF

Brands by name

Popular brands