Polaris 2014 Sportsman 570 EF Service Manual Download Page 261

Page: 261 / 456

6.27

9924871 R03 - 2014 Polaris Sportsman® 570 EFI Service Manual

23. Install main adapter (Item 8) on puller.

24. Install adapter reducer (Item 9).

25. From outside of clutch cover, insert removal tool

(Item 3) into cover bushing.

26. With inside of cover toward vise, slide cover onto

puller.

27. Install nut onto puller rod and hand tighten. Turn

puller barrel to increase tension as needed.

28. Turn clutch cover counterclockwise on puller rod until

bushing is removed and cover comes free.

29. Remove nut from puller rod and set aside.

30. Remove bushing and bushing removal tool from

puller. Discard bushing.

Cover Bushing Installation

31. Apply Loctite® 648 evenly to bushing bore in cover.

32. Working from inside of cover, insert new bushing and

bushing installation tool into center of clutch cover.

33. With main adapter on puller, insert cover onto puller

rod, placing outside of cover toward vise.

34. Install nut on rod and hand tighten. Turn puller barrel

to apply more tension if needed.

35. Turn clutch cover counterclockwise on puller rod until

bushing is seated.

36. Remove nut from puller rod. Take installation tool

and clutch cover off rod.

CLUTCHING

Summary of Contents for 2014 Sportsman 570 EF


























































































































































































































































































































































































































Search results

Summary of Contents for 2014 Sportsman 570 EF

Reviews:

Related manuals for 2014 Sportsman 570 EF

Brands by name

Popular brands

Polaris 2014 Sportsman 570 EF, Service Manual

Search results

Summary of Contents for 2014 Sportsman 570 EF

Reviews:

Related manuals for 2014 Sportsman 570 EF

Brands by name

Popular brands