Polaris 2014 Sportsman 570 EF Service Manual Download Page 145

Page: 145 / 456

3.87

9924871 R03 - 2014 Polaris Sportsman® 570 EFI Service Manual

TROUBLESHOOTING

Engine

Spark Plug Fouling

• Spark plug cap loose or faulty

• Incorrect spark plug heat range or gap

• PVT system calibrated incorrectly/ components

worn or mis-adjusted

• Fuel quality poor (old) or octane too high

• Low compression

• Restricted exhaust

• Weak ignition (loose coil ground, faulty coil, or

stator)

• Restricted air filter (main or pre-cleaner) or breath-

er system

• Improperly assembled air intake system

• Restricted engine breather system

• Oil contaminated with fuel

Engine Turns Over But Fails To Start

• No fuel

• Dirt in fuel line or filter

• Fuel will not pass through fuel valve

• Fuel pump inoperative/restricted

• Tank vent plugged or pinched

• Engine flooded

• Low compression (high cylinder leakage)

• No spark (Spark plug fouled) ignition component

failure

Engine Does Not Turn Over

• Dead battery

• Starter motor does not turn

• Engine seized, rusted, or mechanical failure

Engine Runs But Will Not Idle

• Restricted fuel supply

• Low compression

• Crankcase breather restricted

Engine Idles But Will Not Accelerate

• Spark plug fouled/weak spark

• Broken throttle cable

• Obstruction in air intake

• Air box removed (reinstall all intake components)

• Incorrect flywheel installation or sheared flywheel

key.

• Restricted exhaust system

• Cam worn excessively

Engine Has Low Power

• Spark plug fouled

• Cylinder, piston, ring, or valve wear or damage

(check compression)

• PVT not operating properly

• Restricted exhaust muffler

• Cam worn excessively

Piston Failure - Scoring

• Lack of lubrication

• Dirt entering engine through cracks in air filter or

ducts

• Engine oil dirty or contaminated

Excessive Smoke and Carbon Buildup

• Excessive piston-to-cylinder clearance

• Worn rings, piston, or cylinder

• Worn valve guides or seals

• Restricted breather

• Air filter dirty or contaminated

Piston Failure - Scoring

• Lack of lubrication

• Dirt entering engine through cracks in air filter or

ducts

• Engine oil dirty or contaminated

Slow Engine Cranking

• Weak battery

• Loose Electrical connections

• Decompression

Mechanism

not

functioning

properly.

Excessive Smoke and Carbon Buildup

• Excessive piston-to-cylinder clearance

ENGINE

Summary of Contents for 2014 Sportsman 570 EF


























































































































































































































































































































































































































Search results

Summary of Contents for 2014 Sportsman 570 EF

Reviews:

Related manuals for 2014 Sportsman 570 EF

Brands by name

Popular brands

Polaris 2014 Sportsman 570 EF, Service Manual

Search results

Summary of Contents for 2014 Sportsman 570 EF

Reviews:

Related manuals for 2014 Sportsman 570 EF

Brands by name

Popular brands