Polaris 2014 Sportsman 570 EF Service Manual Download Page 187

Page: 187 / 456

4.41

9924871 R03 - 2014 Polaris Sportsman® 570 EFI Service Manual

Digital Wrench Version and Update ID

Knowing what Digital Wrench version and update is
installed will help determine which updates are required.

NOTE: Versions and updates are subject to change.

Open the Digital Wrench software. Locate the
version ID shown on the lower right side of the Digital
Wrench start-up screen.

Proceed to

http://polaris. diagsys. com

to see if a

newer update is available.

If a newer update is available, it should be
downloaded before using Digital Wrench (see
“Digital Wrench Updates”).

NOTE: Always operate with the latest update.

Digital Wrench Updates

Updates are released for Digital Wrench via the Internet
at:

http://polaris. diagsys. com

. The Digital Wrench

website can also be accessed through the dealer website
at:

www.polarisdealers.com

NOTE:

Only

authorized

Polaris

dealers

and

distributors can access the dealer website.

Log on to

www.polarisdealers.com

Locate the “

Service and Warranty

” drop-down

menu.

Click on “

Digital Wrench Updates

”.

The Digital Wrench portal website should appear in a
new web browser.

Click on “

Digital Wrench Version Updates

”.

NOTE:

You must already have the current

version installed before adding an update.
Updates will not install if you are using an older
version loaded on your PC.

FUEL SYSTEM - GENERAL

Summary of Contents for 2014 Sportsman 570 EF


























































































































































































































































































































































































































Search results

Summary of Contents for 2014 Sportsman 570 EF

Reviews:

Related manuals for 2014 Sportsman 570 EF

Brands by name

Popular brands

Polaris 2014 Sportsman 570 EF, Service Manual

Search results

Summary of Contents for 2014 Sportsman 570 EF

Reviews:

Related manuals for 2014 Sportsman 570 EF

Brands by name

Popular brands