Polaris 2014 Sportsman 570 EF Service Manual Download Page 85 | Manualshive

Page: 85 / 456

background image

3

3.27

9924871 R03 - 2014 Polaris Sportsman® 570 EFI Service Manual

© Copyright 2013 Polaris Sales Inc.

10. Align the water pump drive slot as shown below.

IMPORTANT: The crank shaft and water pump
drive shaft must me aligned for the case to be
assembled.

11. Align the water pump drive shaft blade as shown

below.

12. Apply a small amount of crankcase sealant to the

area indicated below (1).

13. If needed, install the stator cover removal handles

tool PA-49317 to the water cover bolt holes to aid in
stator cover installation.

14. While installing the stator cover to the engine, slightly

rotate the water pump impeller to verify the crankshaft
slot and the water pump drive shaft blade are
properly engaged. Verify the stator cover is laying flat
on the engine case.

NOTE: Image for Reference Only.

CAUTION

The flywheel contains powerful magnets. Use caution

when installing the stator cover.

DO NOT place fingers between cover and crankcase at

any time during the removal and installation process or

injury could result.

CAUTION

If the water pump drive shaft blade and slot in the crank

shaft are not in alignment during the installation

process, severe engine damage may result.

ENGINE

«
...
83
84
85
86
87
...
»

Summary of Contents for 2014 Sportsman 570 EF









































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2014 Sportsman 570 EF

Brand: Baja motorsports Pages: 15

BOSS RT FATBOY 1026RT RR

Brand: Meyer Pages: 44

Brand: Labrie Pages: 172

Brand: Arctic Cat Pages: 160

Brand: Hammerhead Pages: 100

Brand: Yamaha Pages: 141

RAPTOR EFI 110 2024

Brand: Yamaha Pages: 126

Brand: Yamaha Pages: 168

BANSHEE YFZ350M 1999

Brand: Yamaha Pages: 166

GRIZZLY 550 2013

Brand: Yamaha Pages: 176

GRIZZLY 550 2015

Brand: Yamaha Pages: 174

GRIZZLY YFM70GPXK 2017

Brand: Yamaha Pages: 180

Trail Boss 330 Quadricycle

Brand: Polaris Pages: 119

Brand: GMX MOTORBIKES Pages: 57

RANGER XP 1000 2018

Brand: Polaris Pages: 565

Brand: ACG Pages: 97

Brand: ODES Pages: 97

Brand: ULTIMATE TOP DRIVES Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands