Polaris 2014 Sportsman 570 EF Service Manual Download Page 16

Page: 16 / 456

1.12

9924871 R03 - 2014 Polaris Sportsman® 570 EFI Service Manual

Standard Bolt Torque Specification

BOLT SIZE

GRADE 2

FT. LBS. (NM)

GRADE 5

FT. LBS. (NM)

GRADE 8

FT. LBS. (NM)

1/4-20

5 (7)

8 (11)

12 (16)

1/4-28

6 (8)

10 (14)

14 (19)

5/16-18

11 (15)

17 (23)

25 (35)

5/16-24

12 (16)

19 (26)

29 (40)

3/8-16

20 (27)

30 (40)

45 (62)

3/8-24

23 (32)

35 (48)

50 (69)

7/16-14

30 (40)

50 (69)

70 (97)

7/16-20

35 (48)

55 (76)

80 (110)

1/2-13

50 (69)

75 (104)

110 (152)

1/2-20

55 (76)

90 (124)

120 (166)

Metric Bolt Torque Specification

BOLT

SIZE

GRADE

4.6

4.8

8.8 / 8.9

10.9

12.9

FT.— LBS. (NM) DRY THREADS

.3 (.5)

.5 (.7)

1 (1.3)

1.5 (2)

.8 (1.1)

1 (1.5)

2 (3)

3 (4.5)

4 (5)

1.5 (2.5)

2 (3)

4.5 (6)

6.5 (9)

7.5 (10)

3 (4)

4 (5.5)

7.5 (10)

11 (15)

13 (18)

7 (9.5)

10 (13)

18 (25)

26 (35)

33 (45)

M10

14 (19)

18 (25)

37 (50)

55 (75)

63 (85)

M12

26 (35)

33 (45)

63 (85)

97 (130)

11 (150)

M14

37 (50)

55 (75)

103 (140)

151 (205)

177 (240)

M16

59 (80)

85 (115)

159 (215)

232 (315)

273 (370)

M18

81 (110)

118 (160)

225 (305)

321 (435)

376 (510)

GENERAL INFORMATION

Summary of Contents for 2014 Sportsman 570 EF


























































































































































































































































































































































































































Search results

Summary of Contents for 2014 Sportsman 570 EF

Reviews:

Related manuals for 2014 Sportsman 570 EF

Brands by name

Popular brands

Polaris 2014 Sportsman 570 EF, Service Manual

Search results

Summary of Contents for 2014 Sportsman 570 EF

Reviews:

Related manuals for 2014 Sportsman 570 EF

Brands by name

Popular brands