Polaris 2014 Sportsman 570 EF Service Manual Download Page 201

Page: 201 / 456

5.7

9924871 R03 - 2014 Polaris Sportsman® 570 EFI Service Manual

Mud Guard Removal / Installation

Remove front bumper as outline in this chapter.

Locate the mud guards in the front wheel area.

Remove the (1) T27 bolt and the (3) plastic rivets per
side.

Remove the wheel well from the vehicle frame.

Reverse this procedure to reinstall the mud guards.

Torque the T27 fasteners to specification.

T27 Fasteners:

4-6 ft-lbs (6-8 Nm)

BODY / STEERING / SUSPENSION

Summary of Contents for 2014 Sportsman 570 EF


























































































































































































































































































































































































































Search results

Summary of Contents for 2014 Sportsman 570 EF

Reviews:

Related manuals for 2014 Sportsman 570 EF

Brands by name

Popular brands

Polaris 2014 Sportsman 570 EF, Service Manual

Search results

Summary of Contents for 2014 Sportsman 570 EF

Reviews:

Related manuals for 2014 Sportsman 570 EF

Brands by name

Popular brands