Polaris 2014 Sportsman 570 EF Service Manual Download Page 360

Page: 360 / 456

9.16

9924871 R03 - 2014 Polaris Sportsman® 570 EFI Service Manual

Measure the thickness of the pad material. Replace
pads if worn beyond the service limit.

Front Brake Pad Thickness Service Limit:

.180” / 4.6 mm

Assembly

Lubricate mounting bracket pins with a light film of
disc brake caliper lube, and install rubber dust boots.

Compress mounting bracket and make sure dust
boots are fully seated. Install pads with friction
material facing each other.

WARNING

If pads are contaminated with grease, oil, or liquid

soaked do not use the pads. Use only new clean pads.

BRAKES

Summary of Contents for 2014 Sportsman 570 EF


























































































































































































































































































































































































































Search results

Summary of Contents for 2014 Sportsman 570 EF

Reviews:

Related manuals for 2014 Sportsman 570 EF

Brands by name

Popular brands

Polaris 2014 Sportsman 570 EF, Service Manual

Search results

Summary of Contents for 2014 Sportsman 570 EF

Reviews:

Related manuals for 2014 Sportsman 570 EF

Brands by name

Popular brands