Polaris 2014 Sportsman 570 EF Service Manual Download Page 332

Page: 332 / 456

8.14

9924871 R03 - 2014 Polaris Sportsman® 570 EFI Service Manual

29. To disassemble the shift fork rail remove the snap

ring (W) from the end of the shift rail on either side.

CAUTION

Use caution when disassembling the shift rail. The

compressed springs on the shift rail may pop off

causing eye or face injury.

Snorkel Shaft Removal / Disassembly

30. Using a T27 Torx driver, remove the snorkel tube

locking screw located inside the gearcase.

31. Remove the seal from the snorkel shaft to access the

snorkel tube for removal.

32. Using the Snorkel Tool (PA-50231), loosen and

remove the snorkel tube and shaft assembly.

TRANSMISSION

Summary of Contents for 2014 Sportsman 570 EF


























































































































































































































































































































































































































Search results

Summary of Contents for 2014 Sportsman 570 EF

Reviews:

Related manuals for 2014 Sportsman 570 EF

Brands by name

Popular brands

Polaris 2014 Sportsman 570 EF, Service Manual

Search results

Summary of Contents for 2014 Sportsman 570 EF

Reviews:

Related manuals for 2014 Sportsman 570 EF

Brands by name

Popular brands