Polaris 2014 Sportsman 570 EF Service Manual Download Page 170

Page: 170 / 456

4.24

9924871 R03 - 2014 Polaris Sportsman® 570 EFI Service Manual

CPS Replacement

If not done already; disconnect the CPS harness
connector (see “CPS Test”).

Using an 8mm socket, remove the CPS retaining bolt
and remove the sensor from the stator cover.

Install new sensor using a light coating of oil on the
O-ring to aid installation.

Torque the CPS and heat shield retaining bolts (if
equipped) to specification.

CPS Retaining Bolt:

9 ft-lbs (12 Nm)

Re-install the right side footwell and side panel.

FUEL SYSTEM - GENERAL

Summary of Contents for 2014 Sportsman 570 EF


























































































































































































































































































































































































































Search results

Summary of Contents for 2014 Sportsman 570 EF

Reviews:

Related manuals for 2014 Sportsman 570 EF

Brands by name

Popular brands

Polaris 2014 Sportsman 570 EF, Service Manual

Search results

Summary of Contents for 2014 Sportsman 570 EF

Reviews:

Related manuals for 2014 Sportsman 570 EF

Brands by name

Popular brands