manualshive.com logo in svg

Polaris 2014 Sportsman 570 EF, Service Manual

The Polaris 2014 Sportsman 570 EF user manual is a must-have for any owner looking to properly maintain their ATV. This Service Manual provides detailed instructions on maintenance, repair, and troubleshooting. Download your free manual from manualshive.com to keep your vehicle running smoothly for years to come.

Share
Download
background image

10

10.17

9924871 R03 - 2014 Polaris Sportsman® 570 EFI Service Manual

© Copyright 2013 Polaris Sales Inc.

ALL WHEEL DRIVE (AWD) COIL

Operation Overview

• Switch must be set to ‘4x4’. 12Vdc power is present at the AWD hub coil.

• The instrument cluster senses grounding at pin #16. AWD icon should turn on at the instrument cluster.

• System must be grounded to operate.

Diagnosing System Failures

• Verify the AWD switch is functional.

• Verify the AWD hub coil is functional. Test the AWD hub coil using an ohm meter.

AWD Hub Coil Resistance:

24 Ω ± 5%

• Verify the wiring harness, wiring, connectors, connector pins and grounds are undamaged, clean and connect

properly.

• Verify continuity of wire connections with a known good volt/ohm meter.

NOTE: Verify all wires and wiring connections have been tested properly with a known good volt/ohm
meter before suspecting a component failure. A high percentage of electrical issues are caused by bad/
failed connections and grounds.

ELECTRICAL

Summary of Contents for 2014 Sportsman 570 EF









































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2014 Sportsman 570 EF

Eagle TT4 Parts And Service Manual preview
TT4
Brand: Eagle Pages: 170
Suzuki LT-Z400 Service Manual preview
LT-Z400
Brand: Suzuki Pages: 492
Texas Wagon with tilt Manual preview
Wagon with tilt
Brand: Texas Pages: 42
Can-Am OUTLANDER 6x6 2021 Series Operator'S Manual preview
OUTLANDER 6x6 2021 Series
Brand: Can-Am Pages: 204
abi Workman Owner'S Manual & Assembly Instructions preview
Workman
Brand: abi Pages: 12
Polaris Scrambler Service Manual preview
Scrambler
Brand: Polaris Pages: 109
Yamaha PZ50W Owner'S Manual preview
PZ50W
Brand: Yamaha Pages: 88
Yamaha PZ500D Owner'S Manual preview
PZ500D
Brand: Yamaha Pages: 83
Yamaha PRO HAULER YXP1000 Owner'S Manual preview
PRO HAULER YXP1000
Brand: Yamaha Pages: 92
Yamaha Phazer PZ50GTY Owner'S Manual preview
Phazer PZ50GTY
Brand: Yamaha Pages: 98
Yamaha MM700H Owner'S Manual preview
MM700H
Brand: Yamaha Pages: 94
Yamaha Phazer Owner'S Manual preview
Phazer
Brand: Yamaha Pages: 98
Yamaha MM700G Owner'S Manual preview
MM700G
Brand: Yamaha Pages: 96
Yamaha MOTO-4 1987 Owner'S Manual preview
MOTO-4 1987
Brand: Yamaha Pages: 194
Yamaha MM600G Service Manual preview
MM600G
Brand: Yamaha Pages: 287
Erde SY150 Assembly Instructions preview
SY150
Brand: Erde Pages: 4
PRONAR T028KM Operator'S Manual preview
T028KM
Brand: PRONAR Pages: 101
E-Z-GO ST SPORT Owner'S Manual & Service Manual preview
ST SPORT
Brand: E-Z-GO Pages: 84

Brands by name

Popular brands

Load more brands