Polaris 2014 Sportsman 570 EF Service Manual Download Page 252

Page: 252 / 456

6.18

9924871 R03 - 2014 Polaris Sportsman® 570 EFI Service Manual

Spider Removal

Install clutch in holding fixture (PN 2871358-A) and
loosen the spider (counterclockwise) using Clutch
Spider Removal Tool (PN 2870341).

Clutch Holding Fixture:

PN 2871358-A

Spider Removal Tool:

PN 2870341

NOTE:

Moveable Sheave Bushing Inspection

Inspect the Teflon™ coating on the moveable sheave
bushing.

Moveable Sheave Bushing Inspection:

Replace the cover bushing if more brass than

Teflon is visible on the bushing. Refer to bushing

replacement in this chapter.

Roller, Pin, and Thrust Washer Inspection

Inspect all rollers, bushings and roller pins by pulling a
flat metal rod across the roller.

NOTE: The rubber side of the button is positioned
toward the solid roller pin.

Turn roller with your finger. If you notice resistance,
galling, or flat spots, replace rollers, pins and thrust
washers in sets of three.

Inspect to see if roller and bushing are separating.
Bushing must fit tightly in roller.

Use the Roller Pin Tool (PN 2870910) to replace
rollers and pins as necessary.

NOTE: Take care not to damage roller bushing
or bearing surface of the new pin during
installation.

CLUTCHING

Summary of Contents for 2014 Sportsman 570 EF


























































































































































































































































































































































































































Search results

Summary of Contents for 2014 Sportsman 570 EF

Reviews:

Related manuals for 2014 Sportsman 570 EF

Brands by name

Popular brands

Polaris 2014 Sportsman 570 EF, Service Manual

Search results

Summary of Contents for 2014 Sportsman 570 EF

Reviews:

Related manuals for 2014 Sportsman 570 EF

Brands by name

Popular brands