Polaris 2014 Sportsman 570 EF Service Manual Download Page 380

Page: 380 / 456

9.36

9924871 R03 - 2014 Polaris Sportsman® 570 EFI Service Manual

TROUBLESHOOTING

Brakes Squeal

• Dirty/contaminated friction pads

• Improper alignment

• Worn disc

• Worn disc splines

Poor Brake Performance

• Air in system

• Water in system (brake fluid contaminated)

• Caliper/disc misaligned

• Caliper dirty or damaged

• Brake line damaged or lining ruptured

• Worn disc and/or friction pads

• Incorrectly adjusted lever

• Incorrectly adjusted stationary pad

• Worn or damaged master cylinder or components

• Improper clearance between lever and switch

Lever Vibration

• Disc damaged

• Disc worn (runout or thickness variance exceeds

service limit)

Caliper Overheats (Brakes Drag)

• Compensating port plugged

• Pad clearance set incorrectly

• Auxiliary brake pedal incorrectly adjusted

• Brake lever or pedal binding or unable to return

fully

• Parking brake left on

• Residue build up under caliper seals

• Operator riding brakes

Brakes Lock

• Alignment of caliper to disc

BRAKES

Summary of Contents for 2014 Sportsman 570 EF


























































































































































































































































































































































































































Search results

Summary of Contents for 2014 Sportsman 570 EF

Reviews:

Related manuals for 2014 Sportsman 570 EF

Brands by name

Popular brands

Polaris 2014 Sportsman 570 EF, Service Manual

Search results

Summary of Contents for 2014 Sportsman 570 EF

Reviews:

Related manuals for 2014 Sportsman 570 EF

Brands by name

Popular brands