manualshive.com logo in svg

PerkinElmer CLARUS 590 GC, User Manual

Share
Download
PerkinElmer CLARUS 590 GC User Manual Download Page 87

Setting Up Valves . 87 

 

Setting Up Valves 

The Clarus GC operates six internal solenoid valves.  You can initially configure valves from the 

Configuration screen by selecting the 

Relays

 button.  To change valve settings for your current method 

use the 

Timed Events

 screen and touch the 

Relays

 button. 

Setting the Split Mode Using PPC 

To set the split mode: 

1.

 

Press 

Tools 

menu button

 

and select 

Configuration

. 

 

The Configuration screen appears. 

 

2.

 

Touch the 

Injector 

icon for which you which to configure the split mode. 

The Configure Injector screen appears. 

3.

 

Touch the 

Capillary Control 

check box. 

Summary of Contents for CLARUS 590 GC





























































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands