manualshive.com logo in svg

PerkinElmer CLARUS 590 GC, User Manual

Share
Download
PerkinElmer CLARUS 590 GC User Manual Download Page 159

NPD Overview . 159 

 

 

Activating the NPD Bead 

The bead requires an activation step prior to use. 

Do not inject a sample during Activation.

  

To Activate the bead, carefully follow this procedure in sequential steps below: 

1.

 

Turn the bead potentiometer dial clockwise to apply current to the bead. 

2.

 

Slowly increase the NPD control voltage potentiometer to a setting of 700. 

NOTE:  The bead will gradually acquire an orange glow at this point. 

3.

 

Wait for 5 minutes then increase the potentiometer to 750. 

4.

 

After 1 minute move the potentiometer to 800. 

5.

 

After 1 minute move the potentiometer to 850. 

6.

 

After 1 minute move the potentiometer to 900. 

7.

 

After 1 minute reduce the potentiometer to 850.  

8.

 

After 1 minute reduce the potentiometer to 800.  

9.

 

After 1 minute reduce the potentiometer to 750.  

10.

 

After 1 minute reduce the potentiometer down to 700 

11.

 

For Capillary columns:

 Wait 10 minutes, go to the NPD detector screen, then adjust the 

potentiometer so that the NPD baseline response reads around 0.5 mV on Range 1. Then set the 

desired column flow for the application to be run. 

For Packed Columns:

 Wait 10 minutes, go to the NPD detector screen, then adjust the 

potentiometer down to 500 or below to drop the bead below the active level. Remove the Detector 

Cap Nut (P/N N9300061) and reconnect the column to the detector. Set the desired column flow 

Summary of Contents for CLARUS 590 GC





























































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands