PerkinElmer CLARUS 590 GC User Manual Download Page 186

Page: 186 / 284

186 . Clarus 590 GC User’s Guide

Setting the TCD Current (Filament Current)

CAUTION

ATTENTION

When the detector is not in use the temperature and

current must be off.
Lorsque le détecteur n'est pas utilisé, la température et le

courant doivent être éteints.

From the System Status screen touch the TCD icon

In the TCD tab page touch the

Current

field

and use drop down menu to change

the value. TCD range options are 0 (Off), 1, 2, 3, 4 (maximum sensitivity) and

−

1,–2, –3, or

−

4. A

negative value reverses the polarity.

The TCD range values corresponding to bridge current are shown below:

Summary of Contents for CLARUS 590 GC





























































































































































































































































































Search results

Summary of Contents for CLARUS 590 GC

Reviews:

Brands by name

Popular brands

PerkinElmer CLARUS 590 GC, User Manual

Search results

Summary of Contents for CLARUS 590 GC

Reviews:

Brands by name

Popular brands