PerkinElmer CLARUS 590 GC User Manual Download Page 270

Page: 270 / 284

270 . Clarus 590 GC User’s Guide

Detector Settings

Flame Ionization Detector (FID)

For the FID detector touch the

FID (FIDW)

icon

to get to the FID (FIDW) tab.

To program the temperature in the FID tab touch the

Temperature field

and it will go black.

Then use the plus minus keys to get to the required temperature for your application. Repeat the

same procedure for the

Atten

(attenuation). As shown in the example below, this analysis has

the heater off.

If you require the heater on for your analysis just touch the

heater

button and it will toggle to

heater on.

To have the detector autozero the baseline to a fixed amount touch the

AutoZero

field for the

check mark to appear.

The

Gas flows, Offset, Filter, and Flameout

are shown above as reference fields and they

cannot be changed in this screen.

Summary of Contents for CLARUS 590 GC





























































































































































































































































































Search results

Summary of Contents for CLARUS 590 GC

Reviews:

Brands by name

Popular brands

PerkinElmer CLARUS 590 GC, User Manual

Search results

Summary of Contents for CLARUS 590 GC

Reviews:

Brands by name

Popular brands