manualshive.com logo in svg

PerkinElmer CLARUS 590 GC, User Manual

Share
Download
PerkinElmer CLARUS 590 GC User Manual Download Page 118

118 . Clarus 590 GC User’s Guide

 

 

CAUTION 

ATTENTION 

To ensure proper auto-ignite FID operation, make sure your 

column is positioned in the FID 3.74 inches (95 mm) from the 

back of the column nut. 
Flame ignition may not occur if your carrier gas flow is 60 

mL/min or higher. 
Pour assurer un fonctionnement correct de l'auto-inflammation 

FID, assurez-vous que votre colonne est positionnée dans le 

FID à 2,74 pouces (95 mm) à l'arrière de l'écrou de la colonne. 
La flamme peut ne pas s'allumer automatiquement si le débit 

de votre gaz porteur est de 60 mL / min ou plus. 

1.

 

Touch the 

FID (FIDW)

 icon from the System Status screen. 

The FID tab page appears:

 

 

 

NOTE:  For proper ignition to occur, the FID must be heated to at least 100 

°

C. 

2.

 

Touch the temp field 

 and use the up and down arrow or keypad 

 

buttons to enter a setpoint of at least 100 

°

C, or enter a value 50 

°

C higher than the highest 

temperature of your oven program. 

3.

 

Wait for the FID temperature to become READY.  When the temperature is ready a green light 
appears next to the temperature display 

. 

4.

 

Touch the 

Ignite

 button 

. 

(Note the signal level in mV before the flame ignites.) 

5.

 

Upon pressing the Ignite button, the air flow turns off for 15 seconds, 

Flame Ignition 1 

appears 

in the status bar, and the glow plug begins to glow.

 

Summary of Contents for CLARUS 590 GC





























































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands