PerkinElmer CLARUS 590 GC User Manual Download Page 226

Page: 226 / 284

226 . Clarus 590 GC User’s Guide

External Configuration

Run/ AutoSampler

Pre wash

is number of times the syringe is filled with the sample and emptied to a waste vial

before a sample is acquired for injection. The default is 2. Permissible entries are 0 to 15.

Pump

is the number of times the syringe is filled with the sample before it is acquired for

injection. The default is 6. Permissible entries are 0 to 15.

Post-inject

is the number of times the syringe if filled with solvent and emptied to waste after

sample injection. The first half of these washes is taken from solvent vial 1 or 3. The second half

from solvent vial 2 or 4.The default is 2. Permissible entries are 0 to 15.

Injection Mode

Fast

– 30 millesectonds. Not available when a 50.0 syringe is installed.

Normal

injection takes about 1 second.

Slow

takes about 7.5 second.

Auto resume

provides option for autosamplers program to automatically resume where it left

off should a power failure occur.

Summary of Contents for CLARUS 590 GC





























































































































































































































































































Search results

Summary of Contents for CLARUS 590 GC

Reviews:

Brands by name

Popular brands

PerkinElmer CLARUS 590 GC, User Manual

Search results

Summary of Contents for CLARUS 590 GC

Reviews:

Brands by name

Popular brands