manualshive.com logo in svg

PerkinElmer CLARUS 590 GC, User Manual

Share
Download
PerkinElmer CLARUS 590 GC User Manual Download Page 213

Using the Tools Menu . 213 

 

 

Injectors 

(Deconfiguring and Configuring Injectors)

 

Occasions may arise when you may not be using one of the injectors for an extended period of time. 

Instead of turning off the injector heater, you may find it more convenient to "deconfigure" the unused 

injector.  When you do this, the injector temperature screen for the deconfigured injector will not appear 

in the method. 
Every Clarus GC purchased has been configured at the factory for the specific injector(s) that have been 

installed. You can check the injector configuration of your Clarus GC from the Configuration Mode. 
If one of the detectors has been deconfigured, analog data from the remaining detector will be routed to 

both

 output channels. Both detectors should not be deconfigured at the same time. 

Deconfiguring the detectors also deconfigures the detector’s PPC control.  You must reconfigure the PPC 

control when restoring the detector configuration. 

1.

 

Touch the 

A-Injector

 button.  The 

Configure Injector A

 appears. 

   

 

2.

 

Select the Injector 

Type

 from the drop-down list: 

The 

Type 

options are: 

None, Packed, Cap, GSV, PSSI, and POC

.  The example below shows 

None

 selected. 

 

 

Summary of Contents for CLARUS 590 GC





























































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands