manualshive.com logo in svg

PerkinElmer CLARUS 590 GC, User Manual

Share
Download
PerkinElmer CLARUS 590 GC User Manual Download Page 166

166 . Clarus 590 GC User’s Guide

 

 

5.

 

Set the 

Filter

 to 

200

.  

The default setting is 200 msec. If you want to improve the signal-to-noise, change the setting to 

800 msec. Then run your standard and observe that the signal remains the same and the noise 

improves. 

 

6.

 

When all the settings are appropriate for your analysis touch 

OK

.  

The FPD tab screen will be now visible and the changes you made in the configuration screen will 

be shown.  

Set the FPD Temperature 

NOTE:  The FPD temperature values must be entered between 250 °C and 450 °C only.  Do not enter any value 

less than 250 °C. 

1.

 

From the system status screen touch the 

FPD

 icon. 

2.

 

The FPD tab page is now visible. 

                          

NOTE:  For proper ignition to occur, the FPD must be heated to at least 250 °C. 

Summary of Contents for CLARUS 590 GC





























































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands