manualshive.com logo in svg

PerkinElmer CLARUS 590 GC, User Manual

Share
Download
PerkinElmer CLARUS 590 GC User Manual Download Page 113

FID Overview . 113 

 

FID Overview  

Flame Ionization Detectors (FID) are mass sensitive and used for the destructive analysis of organic 

compounds. 
As the sample enters the detector, it is mixed with hydrogen and then burned in air, thereby generating 

ions.  The ions are collected and measured by the detector, with their concentration proportional to the 

amount of compound present.  Ion collection is enhanced by a polarized electric field that is created by 

applying a voltage (

+50

V) to the jet tip. The detector sensitivity is affected primarily by the hydrogen flow. 

The FID has 

flameout

 detection and an 

auto-ignite

 feature.  Flameout detection occurs 0.5 minutes into 

the 

PRE-RUN

 time and it measures the user-entered baseline threshold level in mV.  If the threshold level 

is exceeded, the flame is considered lit, otherwise the Clarus GC detects that the flame is out and auto-

ignite automatically lights the flame before the start of a run. You can also manually light the flame at any 

time by pressing the Ignite button 

 

. 

A cross section view of a FID is shown below. 

 

Setting Up a PPC FID 

To set up a FID that uses PPC modules, first read the FID setup summary, then follow these procedures. 

FID Setup Summary 

To set up the PPC version of the FID: 

•

 

Set the air and hydrogen flows. 

•

 

Automatically ignite the flame. 

•

 

Manually ignite the flame. 

Summary of Contents for CLARUS 590 GC





























































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands