PerkinElmer CLARUS 590 GC User Manual Download Page 144

Page: 144 / 284

144 . Clarus 590 GC User’s Guide

The following figure shows an installed PID.

Setting Up a PID

To set up a PID, read the PID setup summary, then follow the steps.

PID Setup Summary

To set up a PID:

•

Turn on the oven and the detector heaters.

•

Adjust the make-up gas.
Adjust the make-up gas flow if using a capillary column at flows of

≤

10 mL/min.

•

Turn on the UV lamp.

•

Optimize the lamp intensity.

Turn on the Oven and the Detector Heaters

NOTE: A PID can only be installed in the Detector 2 position (rear).

Close the oven door. This turns on the oven heater.

From the System Status screen touch the PID icon

Summary of Contents for CLARUS 590 GC





























































































































































































































































































Search results

Summary of Contents for CLARUS 590 GC

Reviews:

Brands by name

Popular brands

PerkinElmer CLARUS 590 GC, User Manual

Search results

Summary of Contents for CLARUS 590 GC

Reviews:

Brands by name

Popular brands