manualshive.com logo in svg

PerkinElmer CLARUS 590 GC, User Manual

Share
Download
PerkinElmer CLARUS 590 GC User Manual Download Page 180

180 . Clarus 590 GC User’s Guide

 

 

3.

 

To turn on the photomultiplier tube touch the 

 button in FPD tab screen then touch 

Configuration

 from the drop down menu . This will bring you to the FPD Configuration screen 

page. 

 

4.

 

In the PMT Voltage field set the percentage (see note below) by using the plus minus buttons. This 

will turn on the photomultiplier tube. 

NOTE:  The voltage to the photomultiplier tube has been set in the factory to approximately 70%.  You can change 

this setting from the Clarus GC touchscreen.  You may want to change this setting as the photomultiplier 

tube ages and the signal diminishes.  The signal-to-noise ratio may vary with each photomultiplier tube; 

therefore, increasing the voltage may not increase the signal-to-noise ratio. 

After installing a replacement photomultiplier tube, the noise should be about 2% when the Clarus GC 

integrator output is set to attenuation 8 (x8) and the linearizer off.  See the 

Clarus 590 GC Hardware Guide

 

"Maintenance” chapter, for this procedure. 

NOTE:  The photomultiplier tube can be damaged if exposed to light while voltage is ON.  Never remove the 

detector cap or Photomultiplier tube WITH the voltage on. 

Ignite the Flame 

1.

 

Open the electronics cover to access the ignitor assembly. 

 

2.

 

From the system status screen touch the 

FPD

 icon. 

3.

 

The FPD tab page is now visible. 

Summary of Contents for CLARUS 590 GC





























































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands