manualshive.com logo in svg

PerkinElmer CLARUS 590 GC, User Manual

Share
Download
PerkinElmer CLARUS 590 GC User Manual Download Page 105

Controlling the Autosampler . 105 

 

Program 1 and Program 2 Tabs 

 

1.

 

These two tabs allow for multi-program mode.  

2.

 

Select the method from the drop down menu.  

3.

 

Highlight the 

Vials

, 

Vol

 and 

Injections/Vail

 fields and use the plus minus buttons to input the 

correct amount. 

4.

 

Select either Injector A or B. 

5.

 

Touch 

Start

 when you are ready to begin the autosampler run. 

Autosampler Tasks Tab 

 

The Autosampler Tasks tab includes buttons to execute tasks such as 

Park

 and 

Clean

.  

Touch the 

Park 

button to park the autosampler tower. 

NOTE:  If the syringe is directly over the injector, you should move it by selecting Park. 

Touch the 

Clean

 button to clean the syringe plunger with the solvent wash. 

NOTE:  The Clean option is only available when the autosampler has stopped. 

Summary of Contents for CLARUS 590 GC





























































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands