manualshive.com logo in svg

PerkinElmer CLARUS 590 GC, User Manual

Share
Download
PerkinElmer CLARUS 590 GC User Manual Download Page 179

FPD Overview . 179 

 

 

9.

 

Measure the flow rate. 
For best accuracy, use a soap bubble flowmeter volume that gives a reading of at least 30 seconds. 

10.

 

Obtain a flow rate of about 90 mL/min by repeatedly adjusting the air flow with the pressure 

regulator and measuring the flow. 

NOTE:  Both the carrier gas and combustion gases (air and hydrogen) exit through the FPD.  For satisfactory 

operation of the FPD, a flow rate of 90 mL/min of air is required.  If a column is attached to the FPD, and 

the carrier gas is flowing, the carrier gas flow rate should be added to the required air flow.  For example, if 

the carrier gas flow is 30 mL/min, adjust the air flow until the measured total flow rate (combined carrier 

gas and air) is about 120 mL/min. 

11.

 

Remove the flowmeter. 

12.

 

Touch 

OK

 once the proper air flow has been achieved. 

Turn On the Photomultiplier Tube 

1.

 

From the System Status screen touch the FPD icon. 

2.

 

The FPD tab page is now visible. 

 

 

Summary of Contents for CLARUS 590 GC





























































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands