manualshive.com logo in svg

PerkinElmer CLARUS 590 GC, User Manual

Share
Download
PerkinElmer CLARUS 590 GC User Manual Download Page 183

Detector Temperatures . 183 

 

Detector Temperatures 

To display or change detector temperatures and turn the detector heaters on or off can all be done from 

one screen in the Clarus GC. The example shown below assumes that the Clarus has an ECD detector.  

1.

 

In the System Status screen touch the 

ECD

 icon 

. 

 

2.

 

In the ECD tab locate the 

Make Up

 field. To change the setting touch 

Tools

 and touch 

Configuration

 from the drop down menu. 

 

3.

 

In the ECD tab page touch the temp field 

 and use the up and down arrow  or keypad 

 buttons to add an ECD temperature appropriate for the analysis to be run. 

4.

 

To turn the heater On or Off just touch the 

Heater

 button 

.  The message on the 

button will toggle to either on or off and will be visible on the screen. 

Summary of Contents for CLARUS 590 GC





























































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands