PerkinElmer CLARUS 590 GC User Manual Download Page 277

Page: 277 / 284

Autosampler . 277

Autosampler

Touch the

Run

button to display the Autosampler setting screen.

The Autsosampler screen allows you to select the method from the drop down window. Once you

select the method you want to use for your application, the injection count down will begin.

When the countdown goes to zero the analysis will begin. If you need to stop the autosampler

run touch the

Stop

button.

If you need to modify the method for running the autosampler or enable the autosampler touch

the

Tools

button and from the drop down menu touch

Configuration

Touch the

Run

button

on the

Configuration

screen. The following screen displays.

In the AutoSampler Configuration screen check off the

Enable Autosampler

field by touching

it.
If your application requires Recycling and/or Auto Resume touch the field to check off. Use the

drop down window to set the volume and mode type. For the Syringe wash use the plus/minus

Summary of Contents for CLARUS 590 GC





























































































































































































































































































Search results

Summary of Contents for CLARUS 590 GC

Reviews:

Brands by name

Popular brands

PerkinElmer CLARUS 590 GC, User Manual

Search results

Summary of Contents for CLARUS 590 GC

Reviews:

Brands by name

Popular brands