manualshive.com logo in svg

PerkinElmer CLARUS 590 GC, User Manual

Share
Download
PerkinElmer CLARUS 590 GC User Manual Download Page 191

Routing Detector Output . 191 

 

 

7.

 

Once in the FID tab page touch the System icon 

 to return to the System Status screen. 

8.

 

In the System Status screen touch the TCD icon. The TCD tab page will appear. Touch the 

Events

 

tab. 

9.

 

In the Events screen touch the 

Insert 

button. The Timed Events screen will appear. In the drop 

down menu for Events and touch Output B. 

10.

 

Touch the 

time

 field and use the plus minus buttons to input a time that TCD’s output will go to 

the recorder. 

11.

 

Touch the value field and use the drop down to select a positive value (detector 1 is negative, 

detector 2 is positive). 

12.

 

Touch 

OK

 to return to the TCD tab page. 

 

13.

 

Once in the TCD tab page touch the System icon 

 to return to the System Status screen. 

NOTE:  Detector routing remains in effect until changed. If two detectors are installed but only one configured, 

then the output of the configured detector is sent to both output channels. 

Summary of Contents for CLARUS 590 GC





























































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands