PerkinElmer CLARUS 590 GC User Manual Download Page 115

Page: 115 / 284

FID Overview . 115

The default setting is 200 milliseconds. To improve the signal-to-noise, change the setting to 800

milliseconds. This improves the noise but broadens the peak shapes. If you want a faster detector

response, change the setting to 50 milliseconds; however, the noise level may increase.

Touch the

Set

Point

dialog box for the FID

Flameout

; and then use the up and down arrow or

keypad

buttons to enter a flameout detection level in mV (for example 0.1 mV).

NOTE: You must set a Flameout value in millivolts (mV) for the FID auto-ignition feature to work.

For example, 0.3 mV.

Flameout detection occurs 0.5 minutes into the PRE-RUN time and measures the user-entered

baseline threshold level in mV. In this example 0.3 mV are used. If the 0.3 mV threshold level is

exceeded, the flame is considered lit; otherwise, the auto-ignite sequence begins to automatically

ignite the flame.

Touch the

Set Point

dialog box for the

Air

flow and use the plus and minus buttons to set the FID

Air flow to

450

mL/min.

Summary of Contents for CLARUS 590 GC





























































































































































































































































































Search results

Summary of Contents for CLARUS 590 GC

Reviews:

Brands by name

Popular brands

PerkinElmer CLARUS 590 GC, User Manual

Search results

Summary of Contents for CLARUS 590 GC

Reviews:

Brands by name

Popular brands