manualshive.com logo in svg

Omron E5CC-T, Communications Manual

Share
Download
Omron E5CC-T Communications Manual Download Page 86

4   Modbus Communications Procedure

4 - 6

E5

C-T Digital Temperature Controllers Programmable Type Communications Manual (H186)

4-2

Function List

The following table lists the function codes.

Function Code List

Function code

Name

Process

03 (H'03)

Read variable 
(multiple)

This function reads from the variable area.
It is possible to read two or more consecutive variables.

16 (H'10)

Write variable 
(multiple)

This function writes to the variable area.
It is possible to write two or more consecutive variables.
It is also possible to broadcast this function (broadcast 
transmission).

06 (H'06)

Write variable 
(Single/operation 
command) 

This function writes to the variable area and writes operation 
commands.
It is also possible to write to a single parameter by specifying 
the address in 2-byte mode. (This is not supported in 4-byte 
mode.)
It is also possible to broadcast this function (broadcast 
transmission.)

08 (H'08)

Echoback Test

This function performs an echoback test.

Summary of Contents for E5CC-T



























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands