manualshive.com logo in svg

Omron E5CC-T, Communications Manual

Share
Download
Omron E5CC-T Communications Manual Download Page 79

3 - 33

3   Communications Data for CompoWay/F

E5

C-T Digital Temperature Controllers Programmable Type Communications Manual (H186)

3

-2  Status a

nd Statu

s 2

3

  

Status Details

Note1

“Spare” bits are always OFF.

2

When read in setup area 1, the status of the bits will be as follows: 

*

When the control output ON time is less than 30 ms for a control period of 0.1 s or 0.2 s or when it is less than
100 ms for any other control period, the bit is set to “1” and the heater current is held at the last current value.

Bit position

Status

Bit Description

0

1 

Status 
(lower 
word)

0

Heater overcurrent (CT1)

Not generated

Generated

1

Heater current hold (CT1)*

Update

Hold

2

A/D converter error

Not generated

Generated

3

HS alarm (CT1)

OFF

ON

4

Spare

Not generated

---

5

Alarm  4

OFF

ON

6

Input error

Not generated

Generated

7

Potentiometer input error

Not generated

Generated

8

Control output (heating)/open output

OFF

ON

9

Control output (cooling)/close output

OFF

ON

10

HB (heater burnout) alarm (CT1)

OFF

ON

11

HB (heater burnout) alarm (CT2)

OFF

ON

12

Alarm 1

OFF

ON

13

Alarm 2

OFF

ON

14

Alarm 3

OFF

ON

15

Program end output

OFF

ON

Status 
(upper 
word)

16

Event input 1

OFF

ON

17

Event input 2

OFF

ON

18

Event input 3

OFF

ON

19

Event input 4

OFF

ON

20

Write mode

Backup mode

RAM write mode

21

Non-volatile memory

RAM = Non-volatile 
memory

RAM 

≠ 

Non-volatile 

memory

22

Setup area

Setup area 0

Setup area 1

23

AT execute/cancel

AT canceled

AT execution in 
progress

24

RUN/RESET

Run

Reset

25

Communications writing

OFF (disabled)

ON (enabled)

26

Auto/manual switch

Automatic mode

Manual mode

27

Spare

OFF

---

28

Heater overcurrent (CT2)

Not generated

Generated

29

Heater current hold (CT2)

Update

Hold

30

Spare

OFF

---

31

HS alarm (CT2)

OFF

ON

•

Overcurrent: Last 

value 

held

•

A/D converter error:

Last value held

•

Input error:

Last value held

•

Potentiometer input error

Last value held

•

HB and HS outputs:

Cleared

•

Program end output:

Cleared

•

Current hold:

Last value held

•

Heating and cooling outputs, 
open output, close output

Cleared

•

Alarm outputs:

Cleared

Summary of Contents for E5CC-T



























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands