manualshive.com logo in svg

Omron E5CC-T, Communications Manual

Share
Download
Omron E5CC-T Communications Manual Download Page 130

6   Programless Communications

6 - 14

E5

C-T Digital Temperature Controllers Programmable Type Communications Manual (H186)

Note: 1 If nothing is assigned for an upload setting, the corresponding address in the upload area will contain 0. If

nothing is assigned for a download setting, nothing will be done in the download area.

2 If the same value is set for more than one download setting, only the download setting with the lower

number will be valid. The other download setting will be treated as if nothing was assigned. All upload set-
tings are valid even if the same value is set more than once.

Set value

Set value

Upl

oad

 o

r 

Do

wn

loa

d

 Se

tting

s

100

Program 0 Segment 0 Type

Upl

oad

 o

r 

Do

wn

loa

d

 Se

tting

s

140

Program 0 Segment 8 Type

101

Program 0 Segment 0 SP

141

Program 0 Segment 8 SP

102

Program 0 Segment 0 Slope

142

Program 0 Segment 8 Slope

103

Program 0 Segment 0 Time

143

Program 0 Segment 8 Time

104

Nothing assigned.

144

Nothing assigned.

105

Program 0 Segment 1 Type

145

Program 0 Segment 9 Type

106

Program 0 Segment 1 SP

146

Program 0 Segment 9 SP

107

Program 0 Segment 1 Slope

147

Program 0 Segment 9 Slope

108

Program 0 Segment 1 Time

148

Program 0 Segment 9 Time

109

Nothing assigned.

149

Nothing assigned.

110

Program 0 Segment 2 Type

150

Program 0 Segment 10 Type

111

Program 0 Segment 2 SP

151

Program 0 Segment 10 SP

112

Program 0 Segment 2 Slope

152

Program 0 Segment 10 Slope

113

Program 0 Segment 2 Time

153

Program 0 Segment 10 Time

114

Nothing assigned.

154

Nothing assigned.

115

Program 0 Segment 3 Type

155

Program 0 Segment 11 Type

116

Program 0 Segment 3 SP

156

Program 0 Segment 11 SP

117

Program 0 Segment 3 Slope

157

Program 0 Segment 11 Slope

118

Program 0 Segment 3 Time

158

Program 0 Segment 11 Time

119

Nothing assigned.

159

Nothing assigned.

120

Program 0 Segment 4 Type

160

Program 0 Segment 12 Type

121

Program 0 Segment 4 SP

161

Program 0 Segment 12 SP

122

Program 0 Segment 4 Slope

162

Program 0 Segment 12 Slope

123

Program 0 Segment 4 Time

163

Program 0 Segment 12 Time

124

Nothing assigned.

164

Nothing assigned.

125

Program 0 Segment 5 Type

165

Program 0 Segment 13 Type

126

Program 0 Segment 5 SP

166

Program 0 Segment 13 SP

127

Program 0 Segment 5 Slope

167

Program 0 Segment 13 Slope

128

Program 0 Segment 5 Time

168

Program 0 Segment 13 Time

129

Nothing assigned.

169

Nothing assigned.

130

Program 0 Segment 6 Type

170

Program 0 Segment 14 Type

131

Program 0 Segment 6 SP

171

Program 0 Segment 14 SP

132

Program 0 Segment 6 Slope

172

Program 0 Segment 14 Slope

133

Program 0 Segment 6 Time

173

Program 0 Segment 14 Time

134

Nothing assigned.

174

Nothing assigned.

135

Program 0 Segment 7 Type

175

Program 0 Segment 15 Type

136

Program 0 Segment 7 SP

176

Program 0 Segment 15 SP

137

Program 0 Segment 7 Slope

177

Program 0 Segment 15 Slope

138

Program 0 Segment 7 Time

178

Program 0 Segment 15 Time

139

Nothing assigned.

179

Nothing assigned.

Summary of Contents for E5CC-T



























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands