manualshive.com logo in svg

Omron E5CC-T, Communications Manual

Share
Download
Omron E5CC-T Communications Manual Download Page 170

7   Component Communications

7 - 2

E5

C-T Digital Temperature Controllers Programmable Type Communications Manual (H186)

7-1

Component Communications

You can use component communications to connect two or more E5

@

C slaves to the E5

@

C-T master

via RS-485 and then transfer the fixed SP or program SP or change the RUN/RESET status for all of

the Controllers at the same time. If you transfer the fixed SP or program SP or change the RUN/RESET

status of the master (i.e., the Controller with a communications unit number of 0), the set points or

RUN/RESET status of all of the slaves (i.e., the Controllers with communications unit numbers other

than 0) that are connected via RS-485 will change automatically. When you transfer the set points, the

set point from the master can be multiplied by a factor or offset at each slave.

•

Transferring the Program SP (Program SP Mode)

•

Transferring the Fixed SP (Fixed SP Mode)

Note 1

To use component communications, the input type and, if an analog input is used, the decimal point
position must be set to the same values for all of the E5

@

C-T/E5

@

C Controllers. The operation will not

work correctly if the position of the decimal point is different.

2

When the Reset Operation parameter is set to fixed SP operation, the SP mode status will automatically
change according to the RUN/RESET status. In RUN status, the Controller will change to program SP
mode. In RESET status, the Controller will change to fixed SP mode.

3

The E5

@

CT that acts as the master automatically changes the write mode of the slave E5

@

C from backup

mode (mode for writing set values to non-volatile memory) to RAM write mode (supported from July 2016,
items manufactured at our factory (Version 1.2)).

7-1-1

Introduction

25

 0

C

25

 0

C

25

 0

C

0: Master

1: Sla

v

e

Fixed-

v

al

u

e Controllers

E5

C

n: Sla

v

e

RU

N

RU

N

All sla

v

es from 1 to n are a

u

tomatically 

changed in order to RU

N

 stat

u

s and 

the program SP is transferred.

Master changed to 

RU

N

 stat

u

s.

Programma

b

le Controller

E5

C-T

Fixed SP of master changed to 100.

25

 0

C

25

 0

C

25

 0

C

0: Master

1: Sla

v

e

n: Sla

v

e

SP=90

SP=120

The set point of each 

sla

v

e can 

b

e calc

u

lated.

Fixed SP of master 

changed to 100.

Summary of Contents for E5CC-T



























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands