manualshive.com logo in svg

Omron E5CC-T, Communications Manual

Share
Download
Omron E5CC-T Communications Manual Download Page 102

5   Communications Data for Modbus

5 - 8

E5

C-T Digital Temperature Controllers Programmable Type Communications Manual (H186)

Address

Parameter name

Setting (monitor) value

Level

Four-byte 

mode

Two-byte 

mode

0C00

2C00

Input Type

H'00000000 (0): 

Pt (

−

200 to 850

°

C/

−

300 to 1500°F)

H'00000001 (1): 

Pt (

−

199.9 to 500.0

°

C/

−

199.9 to 900.0°F)

H'00000002 (2): 

Pt (0.0 to 100.0

°

C/0.0 to 210.0°F)

H'00000003 (3): 

JPt (

−

199.9 to 500.0

°

C/

−

199.9 to 900.0°F)

H'00000004 (4): 

JPt (0.0 to 100.0

°

C/0.0 to 210.0°F)

H'00000005 (5): 

K (

−

200 to 1300

°

C/

−

300 to 2300°F)

H'00000006 (6): 

K (

−

20.0 to 500.0

°

C/0.0 to 900.0°F)

H'00000007 (7): 

J (

−

100 to 850

°

C/

−

100 to 1500°F)

H'00000008 (8): 

J (

−

20.0 to 400.0

°

C/0.0 to 750.0°F)

H'00000009 (9): 

T (

−

200 to 400

°

C/

−

300 to 700°F)

H'0000000A (10):  T (

−

199.9 to 400.0

°

C/

−

199.9 to 700.0°F)

H'0000000B (11):  E (

−

200 to 600

°

C/

−

300 to 1100°F)

H'0000000C (12):  L (

−

100 to 850

°

C/

−

100 to 1500°F)

H'0000000D (13):  U (

−

200 to 400

°

C/

−

300 to 700°F)

H'0000000E (14):  U (

−

199.9 to 400.0

°

C/

−

199.9 to 700.0°F)

H'0000000F (15):  N (

−

200 to 1300

°

C/

−

300 to 2300°F)

H'00000010 (16):  R (0 to 1700

°

C/0 to 3000°F)

H'00000011 (17):  S (0 to 1700

°

C/0 to 3000°F)

H'00000012 (18):  B (100 to 1800

°

C/300 to 3200°F)

H'00000013 (19):  W (0 to 2,300

°

C/0 to 3,200

°

F)

H'00000014 (20):  PLII (0 to 1,300

°

C/0 to 2,300

°

F)

H'00000015 (21):  Infrared temperature sensor (K 140

°

F/60

°

C)

H'00000016 (22):  Infrared temperature sensor (K 240

°

F/120

°

C)

H'00000017 (23):  Infrared temperature sensor (K 280

°

F/140

°

C)

H'00000018 (24):  Infrared temperature sensor (K 440

°

F/220

°

C)

H'00000019 (25):

4 to 20 mA

H'0000001A (26):

0 to 20 mA

H'0000001B (27):

1 to 5 V

H'0000001C (28):

0 to 5 V

H'0000001D (29):

0 to 10 V

Initial setting

0C02

2C01

Temperature Unit

H'00000000 (0): °C
H'00000001 (1): °F

0C12

2C09

Scaling Lower Limit

H’FFFFF831 to scaling upper limit 

−

1 

(

−

1999 to scaling upper limit 

−

1)

0C16

2C0B

Scaling Upper Limit

Scaling lower limit + 1 to H'0000270F
(Scaling lower limit + 1 to 9999)

0C18

2C0C

Decimal Point

H'00000000 to 00000003 (0 to 3)

0C22

2C11

Burnout Method

H'00000000 (0): Upscale
H'00000001 (1): Downscale

Initial setting

0D06

2D03

Control Output 1 Signal

H'00000000 (0): 4 to 20 mA
H'00000001 (1): 0 to 20 mA

0D08

2D04

Control Output 2 Signal

H'00000000 (0): 4 to 20 mA
H'00000001 (1): 0 to 20 mA

0D1E

2D0F

SP Upper Limit

The range of values (without decimal point) is as follows: 
Temperature input: SP lower limit + 1 to Input range upper limit
Analog input: SP lower limit + 1 to Scaling upper limit

0D20

2D10

SP Lower Limit

The range of values (without decimal point) is as follows: 
Temperature input: Input range lower limit to SP upper limit 

−

 1

Analog input: Scaling lower limit to SP upper limit 

−

 1

0D22

2D11

Standard or Heat-
ing/Cooling

H'00000000 (0): Standard
H'00000001 (1): Heating and cooling

0D24

2D12

Direct/Reverse Operation

H'00000000 (0): Reverse operation
H'00000001 (1): Direct operation

0D26

2D13

Close/Floating

H'00000000 (0): Floating
H'00000001 (1): Close

0D28

2D14

PID ON/OFF

H'00000000 (0): ON/OFF
H'00000001 (1): 2 PID control

Summary of Contents for E5CC-T



























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands