Oki ML63611 User Manual Download Page 163 | Manualshive

Page: 163 / 271

background image

ML63611 User’s Manual

Chapter 12 Serial Port (SIO)

12 – 11

OPTION B (D): 1.5 V (3.0 V), With regulator

circuit for LCD bias

OPTION A (C): 1.5 V (3.0 V), Without regulator

circuit for LCD bias

(8) Serial port status register (SSTAT)

SSTAT is a 4-bit special function register (SFR) used to indicate the status of serial port send/receive.

SSTAT is initialized to “0” at system reset.

SSTAT is a read-only register, and the content is reset every time it is read.

bit 3: BFULL (send Buffer FULL flag)

This bit is enabled in both UART and synchronous modes, and is set to “1” when send data is set
to STBUFL/H in the send mode, and reset to “0” when the send data is transferred to the send
register.
When BFULL is set to “1” and send data is set (written) to STBUFL/H, the previous data set to
those registers is overwritten and lost. Always set data only after verifying that the BFULL flag
is “0”.

bit 2: PERR (Parity ERRor flag)

This bit is enabled in both UART and synchronous modes, and is set to “1” when the parity for
the received data does not match the parity bit attached to the data.

bit 1: OERR (Overrun ERRor flag)

This bit is enabled in both UART and synchronous modes, and is set to “1” when data reception is
completed and the data received the previous time has still not been transferred to the CPU. In this
case, the new data cannot be transferred to SRBUFL/H.

bit 0: FERR (Framing ERRor flag)

This is only enabled in the UART mode and is set to “1” in the following instances.

(1) when a “1” is detected in start bit sampling
(2) when a “0” is detected in stop bit sampling

In either case a receive interrupt request signal (SRINT) is generated.

BFULL

PERR

OERR

FERR

Send buffer status flag
0 : Send buffer empty (initial value)
1 : Send buffer full

Parity error flag

0 : No parity error (initial value)
1 : Parity error

Overrun flag

0 : No overrun error (initial value)
1 : Overrun error

Framing error

0 : No framing error (initial value)
1 : Framing error

SSTAT (0ADH)

(R)

bit 3

bit 2

bit 1

bit 0

«
...
161
162
163
164
165
...
»

Summary of Contents for ML63611
















































































































































































































































































Reviews:

No comments

Related manuals for ML63611

Brand: EasyIO Pages: 12

Brand: RMG Pages: 6

Brand: Watts Pages: 17

VARIOMATIC SARV 07.1

Brand: AUMA Pages: 32

Brand: Samcen Pages: 65

Brand: Zamel Pages: 2

Brand: Yaesu Pages: 15

Brand: Milesight Pages: 28

SoundLinQ SL2xD2

Brand: Vais Technology Pages: 21

Brand: PACH & COMPANY Pages: 39

AQ Logic Series

Brand: Bernard Controls Pages: 88

Brand: Dawn Pages: 100

Brand: Landi Renzo Pages: 19

Brand: Team Orion Pages: 28

Brand: Kicker Pages: 2

Brand: MPS Pages: 12

Brand: Stahl Pages: 15

Brand: ENGGA Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands