5 Parameter
BU 0200 en-US-4920
139
Pos : 299 /Anleit ungen/El ektr onik /FU und St art er/5. Par ameter/ P0xx Betriebsanz eige @ 0\mod_1327573414463_14638. docx @ 14890 @ 3 @ 1
5.2.1 Operating display
Abbreviations used
•
VFD
= variable frequency drive
•
SW
= software version, stored in P707.
•
S = supervisor parameters
, these are visible or hidden depending on P003.
Parameter
{factory setting}
Setting value/description/note
Supervisor
Parameter
set
Pos : 300 /Anleit ungen/El ektr onik /FU und St art er/5. Par ameter/ Par ameter auflist ung (P000 .. .)/P000- P099/Param et er P000 – Betriebs anzeige @ 0\m od_1327573548773_14638.docx @ 14891 @ @ 1
P000
Operating display
(operating display)
0.01 ... 9999
The operating value selected in parameter P001 is shown
online
in parameterization units with 7-
segment display (e.g. Simple Box).
Important information about the operating mode of the drive can be read out as required.
Pos : 301 /Anleit ungen/El ektr onik /FU und St art er/5. Par ameter/ Par ameter auflist ung (P000 .. .)/P000- P099/Param et er P001 – Ausw ahl Anz eige @ 0\mod_1327573728068_14638. docx @ 14892 @ @ 1
P001
Display selection
(display selection)
0 ... 65
{ 0 }
Selection of status display of a parameterization unit with 7-segment display (e.g.: Simple Box)
0 =
Actual frequency [Hz]
Currently supplied output frequency
1 =
Speed [rpm]
Calculated speed
2 =
Target frequency [Hz]
Output frequency that corresponds to the available setpoint. This
need not correspond with the current output frequency.
3 =
Current [A]
Prevailing measured output current
4 =
Torque current [A]:
torque-generating output current
5 =
Voltage [V AC]
Prevailing alternating voltage present on the device output
6 =
DC link voltage [V DC]
The
DC link voltage
is the internal DC voltage of the VFD. This
depends on the magnitude of the line voltage among other things.
7 =
cos phi
Currently calculated value of the power factor
8 =
Apparent power [kVA]
Calculated prevailing apparent power
9 =
Real power [kW]
Calculated prevailing effective power
10 =
Torque [%]
Calculated prevailing torque
11 =
Field [%]
Calculated prevailing field in motor
12 =
On-time [h]
Time for which line voltage present on device
13 =
Run-time [h]
"Enable operating hours"
is the time for which the device was
enabled.
14 =
Analog input 1 [%]
Current value that is present at analog input 1 of the device
15 =
Analog input 2 [%]
Current value that is present at analog input 2 of the device
16 =
… 18
Reserved, POSICON
19 =
temp. of heat sink [°C]
Current temperature of the heat sink
20 =
usage rate motor [%]
Average motor load based on known motor data (P201...P209).
21 =
usage rate brakeres. [%]
"usage rate brakeres."
is the average braking resistor load based on
known resistor data (P556...P557).
22 =
Inside inverter temp [°C]
Current interior temperature of device
(SK 54xE/SK 2xxE)
23 =
Motor temperature
Measured via KTY-84
24 =
… 29
Reserved
30 =
cur. set value MP-S [Hz]
"Prevailing motor potentiometer function with storage setpoint"
.
(P420…=71/72). Through this function the setpoint can be read out
or pre-set (without the drive running).
31 =
… 39
Reserved
40 =
PLC control box value
Visualization mode for PLC communication
41 =
… 59
Reserved, POSICON
