65E Turbo Motor Grader
Service Manual
9
-
19
Service 2.00_2013.03
Section 9
Moldboard and Implement
Step 10:
Place a dial indicator at the bottom of the
cylinder socket cap, 1. Set to 0.000 mm (0.000 in.).
Step 11:
Use the grader hydraulics to raise the
moldboard. Observe the dial indicator reading.
Movement should be less than 0.127 mm (0.005 in.). If
the clearance is too high, remove socket cap and install
additional shim(s) until clearance is less than 0.127 mm
(0.005 in.).
Step 12:
Apply grease to ball and socket joint.
Step 13:
Place socket cap, 1, on barrel end, 2, of circle
shift cylinder. Using a telescoping gauge and
micrometer, measure inside socket dimension that is in
line with cylinder.
Step 14:
Using a micrometer, measure diameter of
saddle frame ball in approximate direction of circle side
shift operation.
Step 15:
Subtract inside socket measurement, step 13,
from saddle frame ball measurement, step 14. This is
the amount of shims, 3, required.
Step 16:
Remove socket cap, 1.
Step 17:
Insert two bolts, 4, with washers, through
socket cap, 1, and shims, 3, and attach to cylinder, 2.
Torque bolts, 4, to 407
-
475Nm (300
-
350 Ib
-
ft.).
Step 18:
Apply grease to ball and socket joints.
Step 19:
Connect hydraulic lines, 1, to circle shift
cylinder, 2. Torque fittings to 25.8 +/
-
1.3Nm
(19 +/
-
1 Ib
-
ft.).
SADDLE FRAME BALL
Summary of Contents for 65E Turbo Motor Grader
