ZF Friedrichshafen AG
description of fault codes for ERGO-Control
97-09-18
TE-AB
F:\15_Kunden_Informationen\FC_Liste\Fc_37_V920.doc
Seite 18 von 58
Fault
Code
(hex)
SPN FMI Int.
Code
(dec)
MEANING OF THE FAULT CODE
possible reason for fault detection
reaction of the TCU
possible steps to repair
remarks
costu
mer
•
cable is defective and is contacted to
battery voltage
•
cable has no connection to TCU
•
speed sensor has an internal defect
•
connector pin is contacted to battery
voltage or has no contact
32
5140
4
34
S
.
C
.
TO GROUND AT ENGINE SPEED INPUT
TCU measures a voltage less than 0.45V
at speed input pin
•
cable / connector is defective and is
contacted to vehicle ground
•
speed sensor has an internal defect
OP-Mode: substitute clutch
control
•
check the cable from TCU to the sensor
•
check the connectors
•
check the speed sensor
all,
Sisu
33
5140
12
42
LOGICAL ERROR AT ENGINE SPEED INPUT
TCU measures a engine speed over a
threshold and the next moment the
measured speed is zero
•
cable / connector is defective and has
bad contact
•
speed sensor has an internal defect
•
sensor gap has the wrong size
OP-Mode: substitute clutch
control
•
check the cable from TCU to the sensor
•
check the connectors
•
check the speed sensor
•
check the sensor gap
This fault is reset after power
up of TCU
all,
Sisu
34
5150
3
39
S
.
C
.
TO BATTERY VOLTAGE OR O
.
C
.
AT
TURBINE SPEED INPUT
TCU measures a voltage higher than 7.00
V at speed input pin
•
cable is defective and is contacted to
battery voltage
•
cable has no connection to TCU
•
speed sensor has an internal defect
•
connector pin is contacted to battery
voltage or has no contact
OP-Mode: substitute clutch
control
if a failure is existing at output
speed,
TCU shifts to neutral
OP-Mode: limp home
•
check the cable from TCU to the sensor
•
check the connectors
•
check the speed sensor
all,
Sisu
Summary of Contents for 65E Turbo Motor Grader
