ZF Friedrichshafen AG
description of fault codes for ERGO-Control
97-09-18
TE-AB
F:\15_Kunden_Informationen\FC_Liste\Fc_37_V920.doc
Seite 47 von 58
Fault
Code
(hex)
SPN FMI Int.
Code
(dec)
MEANING OF THE FAULT CODE
possible reason for fault detection
reaction of the TCU
possible steps to repair
remarks
costu
mer
closed clutch KV. If this calculated value
is out of range, TCU interprets this as
slipping clutch.
•
low pressure at clutch KV
•
low main pressure
•
wrong signal at internal speed sensor
•
wrong signal at turbine speed sensor
•
wrong size of the sensor gap
•
clutch is defective
if failure at another clutch is
pending
TCU shifts to neutral
OP-Mode: TCU shutdown
•
check main pressure in the system
•
check sensor gap at internal speed
sensor
•
check sensor gap at turbine speed sensor
•
check signal at internal speed sensor
•
check signal at turbine speed sensor
•
replace clutch
B6
5685
2
65
SLIPPAGE AT CLUTCH
KR
TCU calculates a differential speed at
closed clutch KR. If this calculated value
is out of range, TCU interprets this as
slipping clutch.
•
low pressure at clutch KR
•
low main pressure
•
wrong signal at internal speed sensor
•
wrong signal at turbine speed sensor
•
wrong size of the sensor gap
•
clutch is defective
TCU shifts to neutral
OP-Mode: limp home
if failure at another clutch is
pending
TCU shifts to neutral
OP-Mode: TCU shutdown
•
check pressure at clutch KR
•
check main pressure in the system
•
check sensor gap at internal speed
sensor
•
check sensor gap at turbine speed sensor
•
check signal at internal speed sensor
•
check signal at turbine speed sensor
•
replace clutch
all,
Sisu
B7
5700
0
87
OVERTEMP SUMP
TCU measured a temperature in the oil
sump that is over the allowed threshold.
no reaction
OP-Mode: normal
•
cool down machine
•
check oil level
•
check temperature sensor
all,
Sisu
B8
5710
0
88
OVERTEMP RETARDER
TCU measured a temperature in the
retarder oil that is over the allowed
threshold.
TCU disables retarder
OP-Mode: normal
•
cool down machine
•
check oil level
•
check temperature sensor
6WG
B9
5720
0
89
OVERSPEED ENGINE
retarder applies if configured
OP-Mode: normal
-
6WG,
Sisu,
Case
Summary of Contents for 65E Turbo Motor Grader
