65E Turbo Motor Grader
Service Manual
8
-
73
Service 2.00_2013.03
Section 8
Hydraulics
Moldboard Side Shift Cylinder Removal
Step 1:
Support moldboard, 1, with chain and hoist, and
tilt moldboard slightly forward.
Step 2:
Remove four screws, 2, securing two upper
moldboard guides, 3. Remove guides. Using chain and
hoist, tilt moldboard, 1, forward enough on lower
moldboard guides, 4, to access two hydraulic lines, 5.
Disconnect and cap lines from side shift cylinder, 6.
Step 3:
Remove moldboard shift cylinder LH pin retainer
bolt, 7, drive out pin, 8, through cutout in moldboard, 1,
and remove moldboard, 1.
Step 4:
RH pin attaches to moldboard support, 9.
Remove RH pin retainer bolt, 10, drive out RH pin, 11,
then remove shift cylinder, 6.
Moldboard Side Shift Cylinder Installation
Step 1:
Align RH clevis of moldboard shift cylinder, 1,
with RH mounting point on mold
-
board support, 2.
Install pin, 3, then install retainer bolt, 4, through pin,
and secure bolt with nut and washer. Torque retainer
bolt to 14.9 +/
-
1.3 Nm (11 +/
-
1 Ib
-
ft).
Step 2:
Using chain and hoist, position and support
moldboard, 5, on lower support guides, 6. Align LH
clevis of moldboard shift cylinder, 1, with LH mounting
point on moldboard support, 2. Install LH pin, 7, through
cutout in moldboard, then install retainer bolt, 8, through
pin, and secure bolt with nut and washer. Torque
retainer bolt, 8, to 14.9 +/
-
1.3 Nm (11 +/
-
1 Ib
-
ft).
Step 3:
Tilt and support moldboard, 5, forward enough
on lower support guides, 6, to access two hydraulic
lines, 9, and connect lines to moldboard shift cylinder, 1.
Torque fittings to 25.8 +/
-
1.3 Nm (19 +/
-
1 Ib
-
ft).
Summary of Contents for 65E Turbo Motor Grader
