65E Turbo Motor Grader
Service Manual
8
-
65
Service 2.00_2013.03
Section 8
Hydraulics
Assembly
Step 1:
Press bushing, 1, into bottom of case, 2. Install
bushing, 3, and cap, 4, for input shaft, 5. Install
bushing, 6, and cap, 7, in cover, 8.
Step 2:
Insert seal, 9, in bottom hole.
Step 3:
Install output shaft, 10, through seal, 9, and
bushing, 1.
Step 4:
Place key, 11, in output shaft keyway. Using a
hydraulic press, install worm gear, 12, on output
shaft, 10. Be sure key aligns with slot in gear. Gear
should be against shoulder on output shaft
Step 5:
Install bushing, 13, washers, 14, and
snap ring, 15, on input shaft, 5.
Step 6:
Set case on end. Slide input shaft, 5, into
case, 2, far enough to hold first spacer, 16. Orient shaft
with keyway down.
Step 7:
Place key, 17, inside keyway in worm, 18. Retain
with grease.
Step 8:
While holding worm, 1, in position, slide input
shaft, 2, into worm. Rotate input shaft to align key and
keyway. Push input shaft in until visible on opposite side
of worm.
(1) Bushing
(10) Output Shaft
(2) Case
(11) Key
(3) Bushing
(12) Worm Gear
(4) Cap
(13) Bushing
(5) Input Shaft
(14) Washer
(6) Bushing
(15) Snap Ring
(7) Cap
(16) Spacer
(8) Cover
(17) Key
(9) Seal
(18) Worm
Summary of Contents for 65E Turbo Motor Grader
