65E Turbo Motor Grader
Service Manual
Service 2.00_2013.03
8
-
viii
Section 8
Hydraulics
81. If welding is required on an attachment, remove the attachment from the machine.
82. Give complete and undivided attention to the job at hand so that complete control of
the machine is maintained at all times.
83. Under no circumstances should gasoline, alcohol or blended fuels be added to diesel
fuel. These combinations can create an increased fire or explosive hazard. In a closed
container, such as a fuel tank, these blends are more explosive than pure gasoline.
84. Refuel the machine outdoors with the engine shut off. Replace the fuel cap securely.
Use an approved fuel container. Do not smoke when handling fuel. Avoid spilling fuel.
85. Never remove the fuel cap or refuel with the engine running.
86. Do not smoke while refueling the machine or when standing near fuel. Keep any type of
open flame away.
87. Maintain control of the fuel filler nozzle when filling the tank.
88. Do not fill the fuel tank to capacity. Allow room for expansion.
89. Wipe up spilled fuel immediately.
90. Always tighten the fuel tank cap securely.
91. If the original fuel tank cap is lost, replace it with a genuine replacement cap. A non
approved cap may not be safe.
92. Keep equipment clean and properly maintained.
93. Do not drive equipment near open fires.
94. Never use fuel for cleaning purposes.
95. The motor grader is equipped with Roll Over Protection System (ROPS) and a Falling
Object Protection System (FOPS) which must be maintained in a serviceable condition.
96. Do not modify, drill, weld or alter the ROPS or FOPS in anyway. Doing so could render
you liable to legal prosecution in some countries.
97. Never attempt to straighten or weld any part of the main frame or retaining brackets
that have suffered damage. By doing so the structure may be weakened and safety
compromised. Replace all damaged parts.
98. Be careful when driving under bridges or working in confined spaces with low
headroom.
99. Never attach chains or ropes to the ROPS or FOPS for pulling purposes.
100. Never take unnecessary risks even though the ROPS and FOPS provide protection.
Summary of Contents for 65E Turbo Motor Grader
