Naviter Oudie 2, Manual

Page: 157 / 185

Settings 152
© 2003 - 2015 ... Naviter d.o.o.
respond.
.
Range selects max and min values for the vario needle. They can be 5 or 10m/s, 10 or 20kts, 1000 or
2000fpm.
.
Avg selects the averaging interval for the integrator.
. TE Filter selects the filter for Total Energy compensation. The higher the number, the longer it takes for
the vario to show the change in Total energy altitude of the glider.
.
TE Level allows you to compensate for inaccuracies in static pressure/TE tubes. See the LX 1600
manual (chapter 3.2 - Pneumatic Connection) about how to connect the tubes in order to have electronic
compensation (it is different than the tubing when connected to TE pressure compensation).
.
Smart filter is a dynamic filter and controls the rate at which the vario indication moves. Higher
number is slower, more filtered. (see LX1600 documentation for more on this)
. Autozero is used when you notice that the needle is not exactly zero on the ground when nothing is
moving and the wind is calm. Press autozero in a calm environment to re-calibrate vario parameters to
zero.
Speed to fly panel
. Mode selects when the vario sound changes from vario to speed to fly. When set to External it will
use the information from an external switch which you must have installed somewhere in the cockpit. In
the
On circling mode it will change to vario when the glider is circling while it will be in Speed to fly
mode while cruising. Auto speed mode will switch to speed to fly mode when the airspeed becomes
greater than the Spd. value on this same panel.
. Switch style allows you to "invert" the switch operation through the software. Taster option will
change the modes each time the taster is pressed.
.
TAB allows you to select how deep the silent are is (this is an area around zero where speed to fly
indication will not beep).
Write settings to eeprom will save your current settings from both pages (LX 1600 and LX1600-2) to
LX 1600, so they are used even if the PDA is not connected to LX 1600, which can happen in case of
power failure of the PDA.
Audio panel is at the second settings page - LX1600(2).
. Syle lets you choose between the following types of variometer sounds:
.. Lin/neg = The sound changes in linear correlation to the vario reading. It is intermittent at negative
vario values.
.. Lin/pos = The sound changes in linear correlation to the vario reading. It is intermittent at positivevario
values. This is the default setting.
.. Linear = The sound changes in linear correlation to the vario reading. It is not intermittent.
.. Dig/neg = The sound changes in discrete steps. It is intermittent at negative vario values.
.. Dig/pos = The sound changes in discrete steps. It is intermittent at positive vario values.
.. Digital = The sound changes in discrete steps. It is not intermittent at any vario values.
.
SC Style lets you select between SC pos, SC neg and SC. SC pos beeps at positive values, SC neg
beeps at negative values wile SC gives a continous sound at positive values, so you won't mistaken its
beeps with vario sounds.
.
Min.freq. is the sound you will hear when the vario is pegged at -10m/s.
. Zero freq. is the sound you will hear when vario equals zero.
. Max.freq. is the sound you will hear when the vario is pegged at +10m/s
. SC Vol allows you to select between noisy (Vol H) and more silent sound (Vol L) in Speed command
. Test button allows you to see and hear what you have setup. You must be positively connected to LX
1600 in order to test its audio settings.
LCD indicator is found on the second settings page - LX1600(2). It allows you to setup the upper and
lower numbers in the LCD separately for vario and speed command modes.
.
Needle lets you setup what the needle on the indicator shows (Vario, Speed Command, Netto vario or