Mitsubishi Electric City Multi CMB-P1016NU-G, Service Handbook

Page: 97 / 349

- 88 -
[
IV
Remote Controller ]
2. Remote controller function selection via the MA remote controller
E D
G
E
E
E
E
G
G
G
G
G
G
D
D
D
Category 1 Category 3 (Setting content) Category 2
Press the
button.
See [4]-1
Category 3
(Setting content)
Category 1 Remote controller function
selection mode
Category 2
Mode selection
( MODE
SELECTION )
Normal display (Display that appears
when the air condition is stopped)
Language selection
Function lock
Display mode
( DISP MODE
SETTING )
Press the
button.
Press the
button.
Press the
button.
Press the
button.
Press the
button.
Press the
button.
See [4]-2. (1)
See [4]-2. (2)
See [4]-2. (3)
See [4]-3. (1)
See [4]-3. (2)
See [4]-3. (3)
See [4]-3. (4)
See [4]-4. (1)
See [4]-4. (2)
See [4]-4. (3)
Press the
button.
Press the
button.
Press the
button.
Press the button.
Press the button.
Press the button.
NOTE
Timer operation stops when the display is changed from remote controller function selection to normal display.
A
I
B
E
F
G
C
D
H
PAR-21MAA
ON/OFF
FILTER
CHECK
OPERATION
CLEAR
TEST
TEMP.
MENU
BACK DAY MONITOR/SET
CLOCK
ON/OFF
Dot display
Messages are displayed in the
selected language.
All examples in this manual are
given in English
(1) Remote controller function
The settings for the following remote controller functions can be changed in the remote controller function selection mode.
Change the settings as necessary.
[Function selection flowchart]
[1] Stop the air conditioner to start the remote controller function selection mode. [2] Select from category 1. [3] Select from category 2.
[4] Make the setting. [5] Setting completed [6] Go back to the normal display (Finish)
1.Language selection
( CHANGE LANGUAGE )
2.Function lock
( FUNCTION SELEC-
TION )
( MODE SELECTION )
( DISP MODE SETTING )
3.Mode selection
4.Display mode
Select the language in which the menu appears.
(1) Function lock setting ( LOCKING FUNCTION )
(2) Use of automatic mode ( SELECT AUTO MODE )
(3) Temperature range setting ( LIMIT TEMP FUNCTION )
(1) Remote controller main/sub setting ( CONTROLLER MAIN/SUB )
(2) Clock enable/disable function ( CLOCK )
(3) Timer function setting ( WEEKLY TIMER )
(4)Technical assistance contact number setting ( CALL )
(1) Temperature unit selection ( TEMP MODE C/ F )
(2) Suction air temperature display setting ( ROOM TEMP DISP SELECT )
(3) Automatic cooling/heating display setting ( AUTO MODE DISP C/H )
Multi-language display is supported.
Sets the type of locking to put into effect
Enables or disables automatic operation mode
Sets the adjustable temperature range (maximum, minimum)
Sets the remote controller as main or sub
* When two remote controllers are connected to the same group, one controller must be set as sub.
Enables or disables clock function
Sets the timer type
Contact number can be set to appear in case of error.
Sets the telephone number
Sets the temperature unit ( C or F) for display
Switches between display and non-display of indoor (suction) air temperature
Switches between display and non-display of Cool or Heat during
automatic mode
E D
(Press and hold the button and
button simultaneously for two seconds.)
*The settings that are made according to
this procedure are stored in the remote
controller memory.
(Press and hold the button and button simultaneously
for two seconds.)
*The display cannot be changed during function selection,
test run, and self-diagnosis.
Press the button.
( CHANGE LANGUAGE )
( FUNCTION
SELECTION )
D
Function lock setting ( LOCKING FUNCTION )
Use of automatic mode ( SELECT AUTO MODE )
Temperature range setting ( LIMIT TEMP FUNCTION )
Remote controller main/sub setting ( CONTROLLER MAIN/SUB )
Clock enable/disable function ( CLOCK )
Timer function setting ( WEEKLY TIMER )
Technical assistance contact number setting ( CALL )
Temperature unit selection ( TEMP MODE C/ F )
Suction air temperature display setting ( ROOM TEMP DISP SELECT )
Automatic cooling/heating display setting ( AUTO MODE DISP C/H )