Mercury 2010 Milan Owner'S Manual Download Page 66 | Manualshive

Page: 66 / 330

background image

Replacing front side marker bulbs

1. Make sure the headlamp control
is in the off position.

2. From underneath the vehicle,
partially remove the tire splash
shield by removing the press pins.
After removing to allow free access
to the front side marker lamp bulb
and electrical wire harness, the
splash shield should be able to be
repositioned.

3. Rotate the lamp clockwise while holding the electrical connector in
place. After rotating the lamp 90 degrees clockwise, pull and disengage
the wire harness and bulb from the lamp.

4. With the bulb exposed, carefully
remove the bulb from the socket by
grasping the bulb and pulling it
away from the wire harness.

Replace with a new bulb, and reverse the removal steps to complete the
process.

Replacing stop/tail/turn/and side marker bulbs

Your vehicle is equipped with a rear lamp that has a stop/tail and side
marker lamp module containing integral multiple light emitting diodes
(LED). If one or more LEDs burn out, the complete lamp module has to
be replaced. See your authorized dealer for the replacement lamp.

Replacing rear turn signal bulbs

1. Make sure the headlamp switch is in the off position and open the trunk.

2. Lift out trunk floor carpeting panel to access a luggage scuff plate
(hard molding) shingles and a trunk side panel (dark grey, soft
wheelhouse side trim panel) at the lamp area.

3. Carefully pull/push the trunk side panel (dark grey, soft wheelhouse
side trim panel) outboard to expose the lamp assembly. The most

Lights

66

2010 Milan

(mln)

Owners Guide, 3rd Printing
USA

(fus)

«
...
64
65
66
67
68
...
»

Summary of Contents for 2010 Milan











































































































































































































































































































































Reviews:

No comments

Related manuals for 2010 Milan

Gemineye EC2014-C

Brand: Ecco Pages: 10

Reflex 5500 Series

Brand: Ecco Pages: 12

Cushman Turf Truckster

Brand: Jacobsen Pages: 210

CHASSIS CAB 3500 2017

Brand: RAM Pages: 16

Lippert Components LEVELEGS MPD 66385

Brand: Atwood Pages: 6

65 41 2 152 528

Brand: BMW Pages: 21

Road Ready Seat Protector

Brand: Wagan Pages: 12

Brand: Chevrolet Pages: 50

Brand: Roadmaster Pages: 4

CHALLENGER GK-6125A 2018

Brand: Coolster Pages: 45

Brand: Axxess Pages: 16

Brand: Prime Design Pages: 16

Brand: UCANDAS Pages: 4

Brand: Yakima Pages: 8

Brand: Westin Pages: 9

ETSS100CBKFV-BP

Brand: Soundoff Signal Pages: 2

Brand: Mack Pages: 133

Brand: Van Guard Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands