Mercury 2010 Milan Owner'S Manual Download Page 132 | Manualshive

Page: 132 / 330

background image

AIRBAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS)

The passenger airbag cover is a seamless design so that you cannot see
the boundary around its door. The shaded area in the illustration
represents the passenger airbag cover.

WARNING:

Do not put anything on or over the airbag cover.

Placing objects on or over the airbag cover may cause those

objects to be thrown by the airbag into your face and torso or may
result in a failure of the airbag to inflate properly, both of which could
result in serious injury.

Important supplemental restraint system precautions

Airbags DO NOT inflate slowly or
gently and the risk of injury from a
deploying airbag is greatest close to
the trim covering the airbag module.

Seating and Safety Restraints

132

2010 Milan

(mln)

Owners Guide, 3rd Printing
USA

(fus)

«
...
130
131
132
133
134
...
»

Summary of Contents for 2010 Milan











































































































































































































































































































































Reviews:

No comments

Related manuals for 2010 Milan

Brand: Camcar Pages: 6

Brand: LaserTrack Pages: 12

Brand: Uebler Pages: 18

Brand: Axxess Pages: 4

Brand: Vintage Air Pages: 14

Brand: Mazdaspeed Pages: 8

For 1985-1992 GM Cars and Trucks 17933

Brand: Edelbrock Pages: 4

Brand: Haibang Pages: 6

Brand: Whispbar Pages: 15

Brand: AC Schnitzer Pages: 20

VIEWLINE 52 MM - MOUNTING 11-09

Brand: VDO Pages: 4

Brand: Whispbar Pages: 14

Brand: Whelen Engineering Company Pages: 9

Brand: Hella Pages: 21

Brand: tams elektronik Pages: 19

Brand: BrandMotion Pages: 6

Dynamic Power Management Home - Module

Brand: newmotion Pages: 20

Brand: Scosche Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands