Mercury 2010 Milan Owner'S Manual Download Page 126 | Manualshive

Page: 126 / 330

background image

WARNING:

Position the safety belt height adjusters so that the

belt rests across the middle of your shoulder. Failure to adjust

the safety belt properly could reduce the effectiveness of the safety
belt and increase the risk of injury in a collision.

Safety belt pretensioner

Your vehicle is equipped with safety belt pretensioners at the driver and
front outboard passenger seating positions.

The safety belt pretensioner tightens the safety belts firmly against the
occupant’s body at the start of the crash.

WARNING:

The driver and front passenger safety belt system

(including retractors, buckles and height adjusters) must be

replaced if the vehicle is involved in a collision that results in
deployment of front airbags, seat-mounted side airbags and side air
curtains, and safety belt pretensioners.

Safety belt extension assembly

If the safety belt is too short when fully extended, there is an 8 inch
(20 cm) safety belt extension assembly that can be added (part number
611C22). This assembly can be obtained from an authorized dealer.

Use only extensions manufactured by the same supplier as the safety
belt. Manufacturer identification is located at the end of the webbing on
the label. Also, use the safety belt extension only if the safety belt is too
short for you when fully extended.

WARNING:

Do not use extensions to change the fit of the

shoulder belt across the torso.

Seating and Safety Restraints

126

2010 Milan

(mln)

Owners Guide, 3rd Printing
USA

(fus)

«
...
124
125
126
127
128
...
»

Summary of Contents for 2010 Milan











































































































































































































































































































































Reviews:

No comments

Related manuals for 2010 Milan

Brand: B-Speech Pages: 18

Brand: iDataLink Pages: 30

1973 Convertible

Brand: Volkswagen Pages: 80

SmartShot Automatic 12V 1.5 Amp 5 Stage

Brand: Yuasa Pages: 44

Brand: Yutrax Pages: 8

Brand: r.LiNK Pages: 21

Brand: Broadfeet Pages: 2

Brand: JSPORT Pages: 2

Brand: RAM Pages: 148

Brand: Hamron Pages: 36

Perfect Fit MBM120

Brand: Waeco Pages: 3

Brand: Or-Fab Pages: 4

Brand: Mobileye Pages: 29

Brand: IOGear Pages: 38

PRIME DESIGN HRR3-E-PM52

Brand: Safe Fleet Pages: 12

Brand: Prorack Pages: 13

Brand: Connects2 Pages: 2

Brand: Whispbar Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands