Mercury 2010 Milan Owner'S Manual Download Page 291 | Manualshive

Page: 291 / 330

background image

When fail-safe mode is activated

You have limited engine power when in the fail-safe mode, so drive the
vehicle with caution. The vehicle will not be able to maintain high-speed
operation and the engine will run rough. Remember that the engine is
capable of completely shutting down automatically to prevent engine
damage, therefore:

1. Pull off the road as soon as safely possible and turn off the engine.

2. Arrange for the vehicle to be taken to an authorized dealer.

3. If this is not possible, wait a short period for the engine to cool.

4. Check the coolant level and replenish if low.

WARNING:

Fail-safe mode is for use during emergencies only.

Operate the vehicle in fail-safe mode only as long as necessary to

bring the vehicle to rest in a safe location and seek immediate repairs.
When in fail-safe mode, the vehicle will have limited power, will not be
able to maintain high-speed operation, and may completely shut down
without warning, potentially losing engine power, power steering assist,
and power brake assist, which may increase the possibility of a crash
resulting in serious injury.

WARNING:

Never remove the coolant reservoir cap while the

engine is running or hot.

5. Re-start the engine and take your vehicle to an authorized dealer.

Driving the vehicle without repairing the engine problem
increases the chance of engine damage. Take your vehicle to an
authorized dealer as soon as possible.

FUEL FILTER

Your vehicle is equipped with a lifetime fuel filter that is integrated with
the fuel tank. Regular maintenance or replacement is not needed.

Maintenance and Specifications

291

2010 Milan

(mln)

Owners Guide, 3rd Printing
USA

(fus)

«
...
289
290
291
292
293
...
»

Summary of Contents for 2010 Milan











































































































































































































































































































































Reviews:

No comments

Related manuals for 2010 Milan

Brand: Jeep Pages: 608

Brand: Jeep Pages: 603

Brand: Jeep Pages: 80

Brand: RaceChip Pages: 20

Brand: Jeep Pages: 1528

Vehicle Asset Communicator

Brand: I.D. Systems Pages: 41

Brand: Scion Pages: 24

Brand: Volvo Pages: 18

Brand: Navman Pages: 27

Brand: Buick Pages: 394

PRIME DESIGN UXV 211

Brand: Safe Fleet Pages: 8

Brand: 3SIXT Pages: 4

Brand: Axxess Pages: 16

Brand: Prime Design Pages: 16

CommCenter 300MB-SD

Brand: Federal Signal Corporation Pages: 60

Brand: AL-KO Pages: 88

Brand: SEC Pages: 2

Brand: Enduro Pages: 56

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands