Mercury 2010 Milan Owner'S Manual Download Page 162 | Manualshive

Page: 162 / 330

background image

3. Open the tether anchor cover.

4. Clip the tether strap to the
anchor as shown.

If the tether strap is clipped
incorrectly, the child safety seat may
not be retained properly in the
event of a collision.

5. Tighten the child safety seat tether strap according to the
manufacturer’s instructions.

If the safety seat is not anchored properly, the risk of a child being
injured in a collision greatly increases.

If your child restraint system is equipped with a tether strap, and the
child restraint manufacturer recommends its use, Ford also recommends
its use.

Child booster seats

The belt-positioning booster (booster seat) is used to improve the fit of
the vehicle safety belt. Children outgrow a typical child seat (e.g.,
convertible or toddler seat) when they weigh about 40 lb (18 kg) and are
around four (4) years of age. Consult your child safety seat owner guide
for the weight, height, and age limits specific to your child safety seat.
Keep your child in the child safety seat if it properly fits the child,
remains appropriate for their weight, height and age AND if properly
secured to the vehicle.

Although the lap/shoulder belt will provide some protection, children
who have outgrown a typical child seat are still too small for lap/shoulder
belts to fit properly, and wearing an improperly fitted vehicle safety belt
could increase the risk of serious injury in a crash. To improve the fit of

Seating and Safety Restraints

162

2010 Milan

(mln)

Owners Guide, 3rd Printing
USA

(fus)

«
...
160
161
162
163
164
...
»

Summary of Contents for 2010 Milan











































































































































































































































































































































Reviews:

No comments

Related manuals for 2010 Milan

Brand: KC HiLiTES Pages: 4

Brand: Happy Orange Pages: 2

Brand: AA Products Pages: 8

Brand: IAME Pages: 17

Brand: OEM Tools Pages: 4

Brand: Porsche Pages: 144

Brand: Prorack Pages: 14

Brand: Car-Interface Pages: 23

Brand: RuggON Pages: 2

Brand: U & Me Brothers Pages: 6

Brand: PAC Pages: 4

Brand: Jeep Pages: 136

Brand: PEUGEOT Pages: 17

Brand: ULTIMATE SPEED Pages: 34

Brand: Webasto Pages: 23

FABIA II TMB PS 035

Brand: Skoda Pages: 16

PRIME DESIGN HRR3-E-PM52

Brand: Safe Fleet Pages: 12

Brand: Mitsubishi Pages: 57

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands